Installing a 220VAC Circuit For Air Conditioning Condenser Unit

How to install a new 220VAC electrical circuit to an air conditioning condensing unit.

When it comes to air conditioning installations, there is usually very little that the homeowner can do. However if you are relatively handy you can install the electrical service to the outdoor condenser unit and then leave the refrigeration work to the professionals.

Remember that you should always check with your local building department to determine what type of permit is required for the total installation of an air conditioning system. Homeowners are usually allowed to perform electrical and plumbing work without a license. By having the work permitted and inspected you will not only increase the chances for a successful installation, you will not void your homeowner’s insurance policy and you will not have any issues when you go to sell your home in the future.

The Electrical Circuit

The electrical circuit needed to power your outdoor air conditioner condenser is typically a double pole circuit breaker in your home load center (panelboard) that goes to an air conditioner service disconnect switch and from the disconnect switch to the condenser.

A 220 VAC circuit requires two (2) vacant circuit breaker positions located together in the panelboard. From the circuit breaker you will run the appropriate size cable to the outdoor air conditioning disconnect switch. From the disconnect switch you run the wires to the air conditioner. The size of the wire depends on a few important factors; the circuit size which is determined by the unit, the length of the run from the unit to the panelboard, and the insulation on the wire. Also check the installation instructions on the condenser unit. Some models may require both 120VAC and 240 VAC; in this case you would need to run 3-conductor wire, red, black, white and a ground.

You may need to make sure that your electrical service has the capacity for new air conditioning equipment if you are adding it to an existing home. Contact your utility for more information.

Wire Size Calculator: http://www.elec-toolbox.com/calculators/voltdrop.htm

Note: The longer the circuit length the greater the voltage drop. Usually circuits over 40 feet in length need the wire size increased to the next largest wire size. For a 30A circuit you may need #10 wire and for a 45A circuit your may need #8 wire.

Tools and Materials

Voltage Meter or Tester

Drill and Drill Bits

Flat and Philips Screwdrivers

Hammer

Torpedo level

Galvanized screws, for mounting disconnect

Utility Knife

Electrical Tape

Electrician’s Pliers

Wire Strippers

Wire, #12, #10, or #8 and a ground wire

Flexible Liquid-tight conduit

Liquid-tight fittings

Clamps

Knockout fitting

Double-Pole Circuit Breaker

Pullout disconnect

Installation

1. Mount the air conditioner disconnect on the exterior of the home as close to the air conditioner condenser as is reasonable. Ensure that it is securely fastened to the wall using proper fastening hardware for the wall material. The National Electrical Code is typically followed but may be interpreted differently by the building inspector. Usually it needs to be readily accessible and within line of sight which can mean within arm’s reach or within 6 feet. Check with you local code official for clarification.

2. The air conditioner disconnect is connected to the air conditioner condenser with liquid-tight flexible metallic conduit, sometimes referred to as “seal-tight.” The size of the conduit is dependent upon the wire size, for #10 use 1/2” conduit and for #8 use 3/4” conduit. (This is for 2 wire conductors.) Liquid-tight conduit can be purchased at electrical distributors and most home centers.

Liquid-tight Conduit

The conduit is mechanically connected to the disconnect and the condenser using the appropriate straight or 90° flexible metallic conduit fittings. These fittings transition from the PVC coated conduit to a metal fitting

90-Degree Liquid-tight fitting

Add conduit clamps within 12 inches from the disconnect and another at the last point on the wall prior to the conduit heading towards the condenser.

Liquid-tight Clamps

3. Run the appropriately sized wires through the liquid-tight conduit. While you can purchase and run sheathed cable, it is better to purchase individual conductors of the correct wire gauge and length. They can be purchased at electrical distributors and home centers. The length of the wire should be about 24 inches longer than the conduit itself.

Since both wires are conductors in 240VAC circuits, buy wires with black insulation to identify them properly. If you use sheathed cable that has one black and one white wire, you need to wrap the ends on the white wire with black electrical tape.

4. Connect the wires in the air conditioning condenser junction box.

The bare copper wire is the ground wire which needs to be connected to the green wire in the condenser junction box. This may be a lug or screw connection depending on the manufacturer. In either case the ground wire is connected to the metal frame of the air conditioner condenser.

Inside of a Condensing Unit: The liquid-tight conduit is coming in at the bottom (1), the two black conductors are connected to the relay on the left (2), and the ground wire is connected to a lug on the left side of the frame (3).

The other 2 wires supply the 220 VAC to the condenser. The location and method of connection for these two wires will be described in the installation manual that came with the condenser.

5. Connect the wires to the inside terminals or lugs in the disconnect. The bare copper wire will attach to a lug or screw that is connected to the frame of the disconnect. The other two wires will connect to lugs or screws that are identified as “LOAD”. It does not matter which load wire goes to which lug or screw. Check with your local code official to determine if they require a fused disconnect, which is not typical, or a non-fused pullout disconnect.

Pullout Service Disconnect

6. Run the wires from the service disconnect to the electrical load center. If the cable is going through an unfinished basement or in a crawl space under a home you can use sheathed cable. However, anywhere where the cable is in a location where it can be damaged it must be protected. For this reason it is better to run the wires inside rigid PVC conduit or the flexible conduit to an electrical junction box and from that point on to the load center.

Use conduit clamps to fasten the conduit to the wall or joists. In areas where sheathed cable is running through a basement the cable must secured using clamps or staples every 36 inches and within 12 inches of any electrical box or the load center panel.

7. Turn the power "OFF" at the load center. This is accomplished by either turning "OFF" the main breaker or at a disconnect switch located between the utilities electrical meter and the load center. You will most likely need to remove a “knockout” from the load center either at the top of bottom. Use a fitting to protect the wires going through the knockout hole.

Knockout fitting

IMPORTANT: Turning the main breaker to the "OFF" position does not remove all power from the load center. Power has been turned "OFF" to the individual circuit breakers, but there is still live power on the incoming lugs of the main breaker.

Remove the inner load center panel that covers the electrical connections to the circuit breakers.

IMPORTANT: When you have turned the power to the "OFF" position, ensure that there is no power at the breakers by using a volt meter.

8. You must install a double pole breaker in the load center panel. The size of the breaker depends on the electrical requirements of your air conditioner condenser. It can be 30, 45, or 60 Amp.

Double-Pole Breakers shown with red and black wires.

A double pole circuit breaker takes up two vertical positions in the load center. If you have two horizontal positions available you can move one of the current circuit breakers in order to free up two vertical breaker positions.

Double-Pole Breaker

Note: Do not install two wires on one circuit breaker in order to free up space.

Note: You must purchase a double pole circuit breaker that is designed for your load center. There is no standard mounting configuration for circuit breakers in load centers. The front of the breaker will have the name of the manufacturer and type which is usually 3 or 4 letters.

Once you have installed the new double pole circuit breakers connect the load wires, one to each of the circuit breaker lugs.

9. Connect the ground wire to the ground bar or lug in the load center panel.

10. Replace the circuit breaker cover panel.

Leave the new double pole circuit breaker "OFF" until the installation of the air condition system has been completed by your HVAC technician.

11. Turn the main breaker or the main disconnect switch back to the "ON" position.

After the system has been completed, call your building inspector for a final inspection.

By taking the time to properly install the electrical service to your air conditioning system you can save yourself a few hundred dollars.

5 comments

Add a comment

0 answers +0 votes
Post comment Cancel
JESUS MENDOZA
0
0 answers Posted on Dec 4, 2015
This comment has 0 votes  by
Aunty Ann
0
548 answers Posted on Jun 8, 2011
This comment has 0 votes  by
Roberta Baxter
0
168 answers Posted on Jun 6, 2011
This comment has 0 votes  by
William J. Felchner
0
851 answers Posted on May 28, 2011
This comment has 0 votes  by
Roberta Baxter
0
168 answers Posted on May 27, 2011
This comment has 0 votes  by

Related Articles

Installing a 220VAC Circuit For Air Conditioning Condenser Unit

When it comes to air conditioning installations, there is usually very little that the homeowner can do. However if you are relatively handy you can install the electrical service to the outdoor condenser unit and then leave the refrigeration work to the professionals. Remember that you should alwa...

How to Size a Circuit Breaker and Wire Sizes

Circuit breakers are over current protection devices (OCPD) that are designed to break the circuit and prevent equipment damage or fire. When too much current runs through a circuit the heat in the circuit exceeds the breaker's load rating and it trips, shutting off the electrical power. Proper sizi...

Troubleshooting a Low Voltage Lighting Transformer

Low voltage lighting transformers have become commonplace in many of today’s homes with the increase awareness in energy efficient lighting systems and decorative accent lighting. A low voltage lighting transformer is a device that converts the standard 110V or 120V household voltage to a lowe...

How To Wire A Fan/Light Switch

Installing a ceiling fan/light combination is a common home improvement project. The part of these projects that confuse many new do-it-yourself persons is how to wire the electrical wiring, so the fan and the light can be controlled by separate, wall-mounted switches. Many handy persons who are rea...

How to Replace Low Voltage Lighting Transformer

Sometimes when a light is not working it isn’t always the bulb. Some recessed lights use a transformer that is mounted to the light above the ceiling. Low-voltage recessed lights use transformers to convert high-voltage electricity to a low-voltage power supply, usually 120V down to 24V or ...

How to Wire a Switched Outlet - Half Hot Outlet

Many times people would like to have an outlet controlled by a switch to be able to turn on a lamp or some other device. Sometimes they have a switched outlet, but it is in the wrong location, or they would like to plug in another device that they would like to remain on all the time. A situation li...

How to Hard Wire a Dishwasher

One of the few appliances in the kitchen that is wired directly to a dedicated circuit is the dishwasher. Aside from the heating element which draws a considerable amount of amperage, the dishwasher is connected to a water source which can pose an elevated risk to shock and circuit overload.  H...

Tricks of the Trade: How to Run Cable Behind Baseboards and Casings

One of the most frustrating things about fishing wire through the walls of older homes is encountering unexpected obstructions. Older homes often have one or more 2 X 4's running horizontally between studs as fire stops. Running wire through such a wall space is very time consuming and labor intensi...

What to Do when a Circuit Breaker Trips Intermittently

A circuit breaker that trips open intermittently may be indicative of a circuit overload or an intermittent short circuits. Two reasons a circuit breaker trips open are circuit overloads and short circuits. Circuit breakers, like the older, Edison-based fuses, are designed to protect electrical writ...

How to Run Electrical Wiring Underground

At some point you may want to have power in a garden shed or detached patio or some other area in your yard. Instead of running an extension cord to that particular location you may want to install an underground conduit or direct burial electrical cable to provide a more permanent solution. Consult...

How to Install or Replace a Doorbell Transformer

Standard doorbells are not powered by 120 volt electric typically used in the home. Most doorbell chimes use a transformer to step down the voltage from 110/120 VAC (volts alternating current) to 10 to 24 VAC. A small transformer is installed in the basement near the door or on the side of the panel...

How to Wire a Lamp

One of the most basic electrical fixtures in your home is a floor or table lamp. If you ever have to rewire a broken lamp or socket, there are some important lamp socket wiring basics you need to understand to correctly connect hot and neutral wires when you replace a lamp switch and socket to keep ...

How to Troubleshoot a Tripped Breaker

Most of the time a, circuit breaker trips people simple go to their electrical panel find the offending breaker and reset it. But what happens when the breaker does not reset, or trips often, you can troubleshoot the problem yourself and depending on the problem, repair it or hire an electrician to ...

How To Test Start And Run Capacitors

Start and run capacitors are found in many single-phase motor circuits and is one of the biggest causes of motor failure. They are found in your refrigerator, deep freezer, air conditioner, furnace, and many of your motor driven power tools. A starting capacitor that has failed or a starting capacit...

How to Replace Fluorescent Light Ballast

Fluorescent light fixtures are energy efficient over the long run, but bulbs and ballasts are expensive replacement items. Typically when the light bulb flickers continuously or the fixture begins to hum you need to replace the ballast. The repair will only take about 10 minutes. New ballast prices ...

DIY ELECTRICAL: An Introduction to Wire and Cable

Since 1930, homes have been wired using nonmetallic sheathed cable (NMC). The original NMC contained two or more rubber insulated conductors within a rubberized fabric jacket. These early NMC wiring systems contained no system grounding conductors. Modern NMC, known as Romex Cable in the trades, has...

How to Install an Outdoor Receptacle

You can install an outdoor electrical receptacle safely and quickly by using a through-the-wall technique. It is important to understand wiring basics, use proper safety precautions and have your work inspected by your local building code official. This method works with homes that do not have stone...

Problems with Your Home's Neutral Wiring

Most homeowners know that their electrical wiring g carries 120 volts of AC (Alternating Current) electricity to outlets, appliances, and switches. They may also know that the black, and sometimes red, wire is the hot wire and the white wire is the neutral. In almost every case the black wire carr...

Homeowner's Guide to Electrical Problems - House Meter Socket

A major component in your home’s electrical system is the main electrical feed coming into the panel board.  Between the utility wires and the panel board is the electric meter which is typically installed in a separate meter box, but sometimes they are installed in a panel board with a s...

How to Move an Electrical Outlet or Light Switch

Electrical outlets and light switches sometimes must be moved during a remodeling project. This often happens when a closet has been added or a door moved. Many times this will leave the light switch on the opposite wall or a large section of the room without an electrical outlet beca...

DIY Appliance Repair: How to Test the High Voltage Components of a Microwave Oven

Once you have removed the outer shell of the microwave oven, you will find a schematic diagram similar to this one affixed either to the inside top or end pieces of the wraparound shell piece. At first glance most of the symbols used on this diagram will probably mean nothing to you, unless you h...

Pros and Cons of the Smart Grid - a National Power Grid for the U.S.

There has been much talk about the initiative to create a “Smart Grid” for the United States electrical power grid. The problems created by the Smart Grid may be equal to or greater than the problems it is meant to solve. A power network utilizing present computing technologies will eli...

Repair Underground Wiring with a Splice Kit

As more and more homeowners add exterior lighting, receptacles, dog fences, and irrigation systems, there is a greater chance for damaging the direct burial, also called underground feeder (UF) cable, underground electrical wires. Instead of digging up the wire and replacing it, you can easily repai...

DIY Electrical: An Introduction to Light Switches

Single—pole light switches are used when the lights are controlled from only one location. Three—way light switches are used when the lights are controlled from two locations. Four—way light switches are used in conjunction with two 3—way light switches when the lights are to...

How to Extend a Coaxial Cable Line

When cable was initially run to homes in the United States only one cable jack was normally installed. As time went on, people often added more televisions that required additional jacks. If you need another jack for a cable TV signal; set up a computer network in your home; or hook up an FM radio o...

How to Fix Buzzing, Noisy, and Flickering Lights

From time to time we have all encountered flickering fluorescent lights or a humming dimmer switch that are more annoying than dangerous. There are plenty of small electrical light problems that you can fix easily without having to hire an electrician and here are a few easy repairs that you can h...

How to Choose the Correct Size Electrical Box

There are many instances when you need to add or move an electrical box during a minor renovation or repair. Whether you are working in your garage, attic, or kitchen you need to know that there is a limit to how many wires you can safely place in an electrical box. Keep in mind that not all electri...

How to Install An Exterior Floodlight

A simple and effective way to improve the safety and security of your home is to add a motion-sensor floodlight over your garage or other area of your home. Many models are available that have a built-in motion sensor which activates the light whenever something crosses its field of vision. The i...

How To Wire A Switch Leg

If you live in an older home, there is an excellent chance that ceiling mounted light fixtures are controlled by pull chain switches. The problem with fixture mounted pull chain switches is that you have to stumble through a pitch black room and fumble around the find the pull chain. It is mush easi...

How To Diagnose and Correct Wiring Problems in Receptacles

Improper or careless wiring of receptacles, also referred to as outlets, is the most common electrical defect found in a typical home. Improperly wired outlets are a potential shock hazard and can cause electrical equipment to use more electricity and fail prematurely. Most of the electronic devic...

DIY Decorator Light Switch Covers with Sharpies

If you have ever seen those cute decorator light switch covers and wanted some for your home you don’t need to buy them. They are priced anywhere from $7.99 and up and are really not that hard to make yourself. The cost for a box of plain white light switch covers from Home Depot is a little...

Facts About Dimmers Switches

Dimmer switches are an effective means to for saving energy and extending bulb life. Along with the practical benefits of placing a light fixture on a dimmer switch, most people utilize dimmers to create visual effects and ambience in a room. Dimming Bulbs 1. Incandescent 2. Halogen The most com...

How to Install an Outdoor Lamp Post

Learn how to install an outdoor lamp post; details include digging a post hole, setting the post and wiring the lamp. Whether you want to add a lamp post alongside your front entry or you need to replace an outdated one, this article will provide the necessary steps to complete the job. Not only do ...

How to Properly Wire a 3-Way Switch

One of the most frustrating things to do is to troubleshoot a 3-way switch that is not working properly. Sometimes the light switch is replaced and the wires were not coded properly to let subsequent people make future replacements easily. This occurred most often in the past when electricians used ...

Recessed Lighting Safety

Recessed lighting has been a part of many homes since the 1970s. Currently Underwriters Laboratories (UL) has a list of approved features for lighting safety. Older recessed lights in your home may require special attention if you are installing new insulation or higher wattage bulbs than the fixt...

The DIY Electrician's Guide to Troubleshooting Dead Receptacles

Knowing how to troubleshoot, isolate and repair electrical problems is what separates the men from the boys-if you’ll excuse the non-politically correct expression-when it comes to electrical work. Almost anyone can install a new receptacle, light switch, light fixture ceiling fan, etc. but...

How to Hang a Chandelier

You can easily replace outdated light fixtures to improve the look of a room. A new ceiling light or chandelier can add style, create a focal point, or improve the lighting of a room. Even though you may not be comfortable working with electricity, switching out old fixtures is safe as long as you p...

How to Use a Circuit Breaker Finder

Have you ever tried to locate the circuit breaker controlling the branch circuit that you want to work on? If you have a relatively new home, the circuit directory may be correct so finding the right breaker is a snap. The circuit directory on breaker panels in older homes is illegible or missing. T...

Tracing and Repairing Speaker Wire in Your Wall

Tracing and repairing speaker wire in your wall is not difficult. You just need a few tools and some patience. If you have moved into a home with speaker wire already weaving through your drywall you may want to take advantage of that and hook up speakers in the various rooms. You will have to trac...

Arc Fault Circuit Interrupters - AFCI Reduce Fire Hazards

An Arc Fault Circuit Interrupter, AFCI for short, is an electrical device that shuts off power to a circuit when arcing conditions are first detected. Normal circuit breakers open in the presence of a short and may not trip before a fire has begun due to arcing. Up to 40,000 home fires can be associ...

How to Light Artwork

If you have seen artwork displayed in a home, gallery, office, retail or other location, you may have noticed how much lighting impacts the presentation. Lighting artwork properly is essential to experience and understand the complete work of art and all of its illustrious detail. Artwork comes in a...

How to Repair A Solar Walkway Light

Many homeowners have installed economical solar powered lights to illuminate their front entrance walkway. Besides the low initial costs, the lights are easily relocated or removed and stored away for the winter. This article will describe how to repair or replace the solar light fixture. LED...

Common Mistakes Made By The DIY Electrician

There is nothing more rewarding then to be able to tell others that you did it yourself, knowing that you did it correctly. The problem is that with electrical work, just because something works does not mean that you have done it correctly. Professional electricians serve a rigorous apprenticeship ...

DIY Electrical: How to Rewire a Floor Lamp or Table Lamp

Restoring table lamps and floor lamps to like new electrical condition provides a completely safe environment for the beginner to learn essential electrical skill sets. Besides offering shockproof, hands-on learning, you can furnish your home with some really beautiful lamps found at garage sales an...

Electrical Tips and Techniques

Some homeowners may understand a few basic wiring principles for switches, outlets, and small fixture installation. Here are a few tips and tricks you can use that will make the job go smoothly and produce a better finished product. Fishing a Wire in a Wall When fishing a wire through a wall, use ...

New Ideal SpliceLine In-line Connector the Optimal Butt Splice

How many times have this happened to you? You have to replace a duplex receptacle because it is no longer holding a plug securely. You have a receptacle in your shop, so you figure you will be able to replace the old one in fifteen minutes. Plenty of time before you have to leave for work. Your wife...

How to Install a USB Wall Receptacle

You probably haven’t realized it, but there is a product that has been on the market for a few years now which combines the convenience of a USB charger with a traditional wall receptacle.  This allows you to charge iPods, iPads, MP3 players, cameras, and smart phones without using the st...

Light Bulb and Lighting Terms

Here is a comprehensive list of terms that you can use for lighting projects in your home and business. Accent Lighting Directional lighting to emphasize a particular object or draw attention to a display item. Ambient Lighting The general lighting present in an area --excluding task lighting an...

How to Install a Bathroom Fan Timer Switch

A simple electrical device can save you a lot of money in electrical, heating and cooling costs, they will also improve the indoor air quality (IAQ) or your home; an automatic timer switch. You can install these devices when upgrading your bathroom or add them to your existing exhaust fan to automat...

How To Install Track Lighting

Track lighting installation has gained steadily since its introduction to the residential market because it track lighting combines a mix of task lighting and directional lighting. Track lighting is also relatively easy for the do it yourselfer to install, especially if you are replacing existing li...