How to Replace Fluorescent Light Ballast

How to replace an old fluorescent light ballast.

Fluorescent light fixtures are energy efficient over the long run, but bulbs and ballasts are expensive replacement items. Typically when the light bulb flickers continuously or the fixture begins to hum you need to replace the ballast. The repair will only take about 10 minutes. New ballast prices range from $15 to $50, which may make replacing the fixture a better choice for outdated units. This is especially true if your fluorescent light uses T12 bulbs instead of the more energy efficient T8 or T5 bulbs. Note: The number after the T stands for how many 1/8th of an inch the diameter of the bulb is. T12 = 12/8 inch which is 1 ½ inch diameter, T8 = 8/8 inch or 1 inch, and T5 = 5/8 inch.

Fortunately the ballast will typically last 15 to 20 years, which in most cases means that the fixture will be replaced before it becomes necessary for the ballast to be replaced. The life expectancy will be reduced depending on the hours of usage and the power quality of the electrical service. Nearby lightning strikes or power surges can damage the fluorescent ballast and lead to premature failure. Fluorescent fixtures installed in cold locations and bad bulbs can also significantly shorten ballast life.

Tools and Materials

4-in-1 screwdriver

Nut driver; You may not need this depending on the size of the socket on your 4-in-1 screwdriver.

Wire stripper

Replacement ballast: Check the model number on the original ballast and take the information to a home center or electrical supply house to purchase the exact replacement.

Wire nuts

Electrical Tape

Instructions

If you do not feel comfortable in doing any electrical repairs, hire a licensed electrician to perform the repairs.

Depending on the number of bulbs in the fixture there can be anywhere from 4 wires for a single bulb fixture to 8 wires for larger multi-bulb light fixtures. The white and black wires are connected to the incoming power from the electrical panel or wall switch and the colored wires deliver power to and from the bulb sockets.

Old and new ballasts

All residential fluorescent light fixtures will operate on standard 120 volt power supply. Older ballasts were color-coded by the supply voltage, yellow for 120V, red for 277V (commercial). Most manufacturers make universal ballasts that can be connected to either 120 or 277 V systems which eliminate this problem.

The ballast is sized by the number and wattage of the light bulbs in the fixture. Older fixtures may have the bulbs wired in parallel which can pose a minor problem with wiring. Most fixtures will have one, two, or three blue wires to supply voltage to the bulb, and only one red wire completing the circuit.

Typical Wiring Diagram

1. Removing the Bulbs and Cover

Unplug the fixture or turn off the power at the wall switch or main electrical panel.

Remove the bulbs by twisting them to clear the tabs in the socket or pull them straight out.

Twist out bulb socket

Pull out bulb socket

Circline fixtures utilize a plug off of the ballast that connects to the prongs on the circular bulb.

Circline fixture

Remove the internal cover to expose the internal wiring and ballast. Typically this cover is held in place by a few screws or tabs. The cover is either slide down to clear the tabs on one side or the cover is squeezed to clear the tabs. Some manufacturers may use clips to secure the cover.

2. Disconnect the Existing Ballast Wiring

The quickest way to remove the bad ballast is to cut the wiring. To ensure you have enough wire, cut the old color-coded wiring (red, blue, and sometimes yellow) about an inch or two from the point where they exit the old ballast. The power supply wiring, the black and the white wires, should already be connected to the incoming electrical wires with wire nuts so these do not need to be cut. Simply untwist the existing wire nuts on the white and black wires and remove the wiring coming from the ballast.

3. Remove the old Ballast

Unscrew the mounting nut to remove the ballast. There may be one or two nuts holding the ballast in place. Be careful to hold the ballast with your free hand to keep it from falling out as they are heavy and can easily damage flooring. Hold onto the old nuts to mount the new ballast.

The ground wire from the power feed is screwed into the fixture and not directly connected to the ballast. It should not need to be touched during the replacement.

4. Installing the new Ballast

Mount the new ballast in the fixture with the old mounting nuts.

Strip the electrical wiring back about 1/2 inch and connect the like-colored wires with wire nuts.

When all of the colored wires are spliced, connect the white wire to the power feed, and then finally the black wire.

With the cover still off, install one new light bulb in the fixture and turn the power on. If the light comes on you can turn off the power and reinstall the ballast cover. To secure the extra wiring you may want to carefully loop the like colored wires together and wrap them with a small piece of electrical tape. You may also want to wrap the wire nuts with a piece of electrical tape if you are worried that they may come loose.

0 comments

Add a comment

0 answers +0 votes
Post comment Cancel

Related Articles

Installing a 220VAC Circuit For Air Conditioning Condenser Unit

When it comes to air conditioning installations, there is usually very little that the homeowner can do. However if you are relatively handy you can install the electrical service to the outdoor condenser unit and then leave the refrigeration work to the professionals. Remember that you should alwa...

How to Size a Circuit Breaker and Wire Sizes

Circuit breakers are over current protection devices (OCPD) that are designed to break the circuit and prevent equipment damage or fire. When too much current runs through a circuit the heat in the circuit exceeds the breaker's load rating and it trips, shutting off the electrical power. Proper sizi...

Troubleshooting a Low Voltage Lighting Transformer

Low voltage lighting transformers have become commonplace in many of today’s homes with the increase awareness in energy efficient lighting systems and decorative accent lighting. A low voltage lighting transformer is a device that converts the standard 110V or 120V household voltage to a lowe...

How To Wire A Fan/Light Switch

Installing a ceiling fan/light combination is a common home improvement project. The part of these projects that confuse many new do-it-yourself persons is how to wire the electrical wiring, so the fan and the light can be controlled by separate, wall-mounted switches. Many handy persons who are rea...

How to Replace Low Voltage Lighting Transformer

Sometimes when a light is not working it isn’t always the bulb. Some recessed lights use a transformer that is mounted to the light above the ceiling. Low-voltage recessed lights use transformers to convert high-voltage electricity to a low-voltage power supply, usually 120V down to 24V or ...

How to Wire a Switched Outlet - Half Hot Outlet

Many times people would like to have an outlet controlled by a switch to be able to turn on a lamp or some other device. Sometimes they have a switched outlet, but it is in the wrong location, or they would like to plug in another device that they would like to remain on all the time. A situation li...

How to Hard Wire a Dishwasher

One of the few appliances in the kitchen that is wired directly to a dedicated circuit is the dishwasher. Aside from the heating element which draws a considerable amount of amperage, the dishwasher is connected to a water source which can pose an elevated risk to shock and circuit overload.  H...

Tricks of the Trade: How to Run Cable Behind Baseboards and Casings

One of the most frustrating things about fishing wire through the walls of older homes is encountering unexpected obstructions. Older homes often have one or more 2 X 4's running horizontally between studs as fire stops. Running wire through such a wall space is very time consuming and labor intensi...

What to Do when a Circuit Breaker Trips Intermittently

A circuit breaker that trips open intermittently may be indicative of a circuit overload or an intermittent short circuits. Two reasons a circuit breaker trips open are circuit overloads and short circuits. Circuit breakers, like the older, Edison-based fuses, are designed to protect electrical writ...

How to Run Electrical Wiring Underground

At some point you may want to have power in a garden shed or detached patio or some other area in your yard. Instead of running an extension cord to that particular location you may want to install an underground conduit or direct burial electrical cable to provide a more permanent solution. Consult...

How to Install or Replace a Doorbell Transformer

Standard doorbells are not powered by 120 volt electric typically used in the home. Most doorbell chimes use a transformer to step down the voltage from 110/120 VAC (volts alternating current) to 10 to 24 VAC. A small transformer is installed in the basement near the door or on the side of the panel...

How to Wire a Lamp

One of the most basic electrical fixtures in your home is a floor or table lamp. If you ever have to rewire a broken lamp or socket, there are some important lamp socket wiring basics you need to understand to correctly connect hot and neutral wires when you replace a lamp switch and socket to keep ...

How to Troubleshoot a Tripped Breaker

Most of the time a, circuit breaker trips people simple go to their electrical panel find the offending breaker and reset it. But what happens when the breaker does not reset, or trips often, you can troubleshoot the problem yourself and depending on the problem, repair it or hire an electrician to ...

How To Test Start And Run Capacitors

Start and run capacitors are found in many single-phase motor circuits and is one of the biggest causes of motor failure. They are found in your refrigerator, deep freezer, air conditioner, furnace, and many of your motor driven power tools. A starting capacitor that has failed or a starting capacit...

How to Replace Fluorescent Light Ballast

Fluorescent light fixtures are energy efficient over the long run, but bulbs and ballasts are expensive replacement items. Typically when the light bulb flickers continuously or the fixture begins to hum you need to replace the ballast. The repair will only take about 10 minutes. New ballast prices ...

DIY ELECTRICAL: An Introduction to Wire and Cable

Since 1930, homes have been wired using nonmetallic sheathed cable (NMC). The original NMC contained two or more rubber insulated conductors within a rubberized fabric jacket. These early NMC wiring systems contained no system grounding conductors. Modern NMC, known as Romex Cable in the trades, has...

How to Install an Outdoor Receptacle

You can install an outdoor electrical receptacle safely and quickly by using a through-the-wall technique. It is important to understand wiring basics, use proper safety precautions and have your work inspected by your local building code official. This method works with homes that do not have stone...

Problems with Your Home's Neutral Wiring

Most homeowners know that their electrical wiring g carries 120 volts of AC (Alternating Current) electricity to outlets, appliances, and switches. They may also know that the black, and sometimes red, wire is the hot wire and the white wire is the neutral. In almost every case the black wire carr...

Homeowner's Guide to Electrical Problems - House Meter Socket

A major component in your home’s electrical system is the main electrical feed coming into the panel board.  Between the utility wires and the panel board is the electric meter which is typically installed in a separate meter box, but sometimes they are installed in a panel board with a s...

How to Move an Electrical Outlet or Light Switch

Electrical outlets and light switches sometimes must be moved during a remodeling project. This often happens when a closet has been added or a door moved. Many times this will leave the light switch on the opposite wall or a large section of the room without an electrical outlet beca...

DIY Appliance Repair: How to Test the High Voltage Components of a Microwave Oven

Once you have removed the outer shell of the microwave oven, you will find a schematic diagram similar to this one affixed either to the inside top or end pieces of the wraparound shell piece. At first glance most of the symbols used on this diagram will probably mean nothing to you, unless you h...

Pros and Cons of the Smart Grid - a National Power Grid for the U.S.

There has been much talk about the initiative to create a “Smart Grid” for the United States electrical power grid. The problems created by the Smart Grid may be equal to or greater than the problems it is meant to solve. A power network utilizing present computing technologies will eli...

Repair Underground Wiring with a Splice Kit

As more and more homeowners add exterior lighting, receptacles, dog fences, and irrigation systems, there is a greater chance for damaging the direct burial, also called underground feeder (UF) cable, underground electrical wires. Instead of digging up the wire and replacing it, you can easily repai...

DIY Electrical: An Introduction to Light Switches

Single—pole light switches are used when the lights are controlled from only one location. Three—way light switches are used when the lights are controlled from two locations. Four—way light switches are used in conjunction with two 3—way light switches when the lights are to...

How to Extend a Coaxial Cable Line

When cable was initially run to homes in the United States only one cable jack was normally installed. As time went on, people often added more televisions that required additional jacks. If you need another jack for a cable TV signal; set up a computer network in your home; or hook up an FM radio o...

How to Fix Buzzing, Noisy, and Flickering Lights

From time to time we have all encountered flickering fluorescent lights or a humming dimmer switch that are more annoying than dangerous. There are plenty of small electrical light problems that you can fix easily without having to hire an electrician and here are a few easy repairs that you can h...

How to Choose the Correct Size Electrical Box

There are many instances when you need to add or move an electrical box during a minor renovation or repair. Whether you are working in your garage, attic, or kitchen you need to know that there is a limit to how many wires you can safely place in an electrical box. Keep in mind that not all electri...

How to Install An Exterior Floodlight

A simple and effective way to improve the safety and security of your home is to add a motion-sensor floodlight over your garage or other area of your home. Many models are available that have a built-in motion sensor which activates the light whenever something crosses its field of vision. The i...

How To Wire A Switch Leg

If you live in an older home, there is an excellent chance that ceiling mounted light fixtures are controlled by pull chain switches. The problem with fixture mounted pull chain switches is that you have to stumble through a pitch black room and fumble around the find the pull chain. It is mush easi...

How To Diagnose and Correct Wiring Problems in Receptacles

Improper or careless wiring of receptacles, also referred to as outlets, is the most common electrical defect found in a typical home. Improperly wired outlets are a potential shock hazard and can cause electrical equipment to use more electricity and fail prematurely. Most of the electronic devic...

DIY Decorator Light Switch Covers with Sharpies

If you have ever seen those cute decorator light switch covers and wanted some for your home you don’t need to buy them. They are priced anywhere from $7.99 and up and are really not that hard to make yourself. The cost for a box of plain white light switch covers from Home Depot is a little...

Facts About Dimmers Switches

Dimmer switches are an effective means to for saving energy and extending bulb life. Along with the practical benefits of placing a light fixture on a dimmer switch, most people utilize dimmers to create visual effects and ambience in a room. Dimming Bulbs 1. Incandescent 2. Halogen The most com...

How to Install an Outdoor Lamp Post

Learn how to install an outdoor lamp post; details include digging a post hole, setting the post and wiring the lamp. Whether you want to add a lamp post alongside your front entry or you need to replace an outdated one, this article will provide the necessary steps to complete the job. Not only do ...

How to Properly Wire a 3-Way Switch

One of the most frustrating things to do is to troubleshoot a 3-way switch that is not working properly. Sometimes the light switch is replaced and the wires were not coded properly to let subsequent people make future replacements easily. This occurred most often in the past when electricians used ...

Recessed Lighting Safety

Recessed lighting has been a part of many homes since the 1970s. Currently Underwriters Laboratories (UL) has a list of approved features for lighting safety. Older recessed lights in your home may require special attention if you are installing new insulation or higher wattage bulbs than the fixt...

The DIY Electrician's Guide to Troubleshooting Dead Receptacles

Knowing how to troubleshoot, isolate and repair electrical problems is what separates the men from the boys-if you’ll excuse the non-politically correct expression-when it comes to electrical work. Almost anyone can install a new receptacle, light switch, light fixture ceiling fan, etc. but...

How to Hang a Chandelier

You can easily replace outdated light fixtures to improve the look of a room. A new ceiling light or chandelier can add style, create a focal point, or improve the lighting of a room. Even though you may not be comfortable working with electricity, switching out old fixtures is safe as long as you p...

How to Use a Circuit Breaker Finder

Have you ever tried to locate the circuit breaker controlling the branch circuit that you want to work on? If you have a relatively new home, the circuit directory may be correct so finding the right breaker is a snap. The circuit directory on breaker panels in older homes is illegible or missing. T...

Tracing and Repairing Speaker Wire in Your Wall

Tracing and repairing speaker wire in your wall is not difficult. You just need a few tools and some patience. If you have moved into a home with speaker wire already weaving through your drywall you may want to take advantage of that and hook up speakers in the various rooms. You will have to trac...

Arc Fault Circuit Interrupters - AFCI Reduce Fire Hazards

An Arc Fault Circuit Interrupter, AFCI for short, is an electrical device that shuts off power to a circuit when arcing conditions are first detected. Normal circuit breakers open in the presence of a short and may not trip before a fire has begun due to arcing. Up to 40,000 home fires can be associ...

How to Light Artwork

If you have seen artwork displayed in a home, gallery, office, retail or other location, you may have noticed how much lighting impacts the presentation. Lighting artwork properly is essential to experience and understand the complete work of art and all of its illustrious detail. Artwork comes in a...

How to Repair A Solar Walkway Light

Many homeowners have installed economical solar powered lights to illuminate their front entrance walkway. Besides the low initial costs, the lights are easily relocated or removed and stored away for the winter. This article will describe how to repair or replace the solar light fixture. LED...

Common Mistakes Made By The DIY Electrician

There is nothing more rewarding then to be able to tell others that you did it yourself, knowing that you did it correctly. The problem is that with electrical work, just because something works does not mean that you have done it correctly. Professional electricians serve a rigorous apprenticeship ...

DIY Electrical: How to Rewire a Floor Lamp or Table Lamp

Restoring table lamps and floor lamps to like new electrical condition provides a completely safe environment for the beginner to learn essential electrical skill sets. Besides offering shockproof, hands-on learning, you can furnish your home with some really beautiful lamps found at garage sales an...

Electrical Tips and Techniques

Some homeowners may understand a few basic wiring principles for switches, outlets, and small fixture installation. Here are a few tips and tricks you can use that will make the job go smoothly and produce a better finished product. Fishing a Wire in a Wall When fishing a wire through a wall, use ...

New Ideal SpliceLine In-line Connector the Optimal Butt Splice

How many times have this happened to you? You have to replace a duplex receptacle because it is no longer holding a plug securely. You have a receptacle in your shop, so you figure you will be able to replace the old one in fifteen minutes. Plenty of time before you have to leave for work. Your wife...

How to Install a USB Wall Receptacle

You probably haven’t realized it, but there is a product that has been on the market for a few years now which combines the convenience of a USB charger with a traditional wall receptacle.  This allows you to charge iPods, iPads, MP3 players, cameras, and smart phones without using the st...

Light Bulb and Lighting Terms

Here is a comprehensive list of terms that you can use for lighting projects in your home and business. Accent Lighting Directional lighting to emphasize a particular object or draw attention to a display item. Ambient Lighting The general lighting present in an area --excluding task lighting an...

How to Install a Bathroom Fan Timer Switch

A simple electrical device can save you a lot of money in electrical, heating and cooling costs, they will also improve the indoor air quality (IAQ) or your home; an automatic timer switch. You can install these devices when upgrading your bathroom or add them to your existing exhaust fan to automat...

How To Install Track Lighting

Track lighting installation has gained steadily since its introduction to the residential market because it track lighting combines a mix of task lighting and directional lighting. Track lighting is also relatively easy for the do it yourselfer to install, especially if you are replacing existing li...